I need help with strings in emu8086. I have initialized a string:
str1 db "0neWord"
And I have an empty string:
str2 db ?
Now I need to check all letters in str1 and copy to str2, but if the letter in str1 is 0, I need to replace it with O. If not, I need to just copy the letter.
How can I do this?
str2 db ? is not an empty string. db stands for "define byte", and that ? means single uninitialized byte.
The db "0neWord" is assembler's convenience, it will compile into series of bytes defined as '0', 'n', 'e', ..., 'd'. There's no such thing as "string" type in assembler, everything is compiled into machine code, which can be viewed as series of bytes. What "type" of data are stored in memory depends on the instructions used to access them, but in the memory everything is just series of bytes and can be viewed as such.
This is probably a good time for you to check emu8086 debugger documentation, and look at the memory at address str1 after loading the code into debugger, to see how it did compile.
So as soon as you will copy second byte from str1 to str2, you will start overwriting some memory you didn't expect to overwrite.
To allocate some fixed size memory buffer you can use for example str2 db 100 DUP(?) doing 100 times ? definition to db, thus reserving 100 bytes of memory there, next bytes of machine code in the same section will be compiled beyond str2+100 address.
To do anything with str1 "string" you need to know:
1) its address in memory, the x86 assembler has many ways how to get that, but two most straightforward are:
mov <r16>,OFFSET str1(r16 is any 16b register)lea <r16>,[str1](does the same thing in this case)
2) its size OR structure. You didn't put any structure there, like nul-terminated strings have byte with value 0 at their end, or DOS int 21h, ah=9 service to display string expects string terminated with dollar sign '$', etc. So you need at least size. And EQU directive of assembler, and "current position" can be used to calculate size of the str1 like this:
str1 db "0neWord"
str1size EQU $-str1 ; "$" is assemblers "current_address" counter
Hm, I tried to verify this first, by reading some docs, but it's very difficult for me to find any good complete emu8086 documentation (found something like "reference", and it's completely missing description of assembler directives).
I wonder why so many people still land on this, instead of linux + nasm/similar, which are completely free, open source and documented.
So let's hope the emu8086 works like MASM/TASM and that I still recall that syntax correctly, then the above mentioned size definition should work. Otherwise consult your examples/docs.
Finally, when you have address, size, and large enough target buffer (again to load it's address you can use OFFSET or lea in emu8086), you can code your task for example in this way:
; pseudo code follows, replace it by actual x86 instructions
; and registers as you wish
; ("r16_something" means one of 16b register, r8 is 8b register)
lea r16_str1,[str1] ; load CPU with address of str1
mov r16_counter,str1size ; load CPU with str1 size value
lea r16_str2,[str2] ; load address of target buffer
loop_per_character:
mov r8_char,[r16_str1] ; read single character
cmp r8_char,'0'
jne skip_non_ascii_zero_char
; the character is equal to ASCII '0' character (value 48)
mov r8_char,'O' ; replace it with 'O'
skip_non_ascii_zero_char:
; here the character was modified as needed, write it to str2 buffer
mov [r16_str2],r8_char
; make both str1/2 pointers to point to next character
inc r16_str1
inc r16_str2
; count down the counter, and loop until zero is reached
dec r16_counter
jnz loop_per_character
; the memory starting at "str2" should now contain
; modified copy of "str1"
; ... add exit instructions ...
Hmm.. turns out the "pseudo code" is full x86 code, you just have to assign real registers to the pseudo ones, and replace them everywhere in source.
I tried to put there very extensive comments (by my point of view), so can understand every instruction used. You should consult each one with Intel's instruction reference guide, cross-reading it with whatever tutorial/lessons you have available for Assembly, until you will feel like you understand what is register, memory, etc.
Also debug the code instruction by instruction, checking the state of CPU (register values, flags) and memory content after each instruction, to get the idea how it works.
There are multiple ways to do that. Here are some examples:
1) With String Instruction:
.model small
.data
str1 db "0neWord$"
size equ $-str1
str2 db size dup ('')
.code
main:
mov ax, @data
mov ds, ax
mov cx, size
cld ; DF might have been set, but we want lodsb to go forwards
lea si, str1
mov ax, 0
mov bx, 0
copyStr:
lodsb ;str1 to al
cmp al, '0'
je alterChar
mov str2[bx], al
jmp continue
alterChar:
mov str2[bx], 'o'
continue:
inc bx
loop copyStr
mov str2[bx], '$'
mov ah, 09h
lea dx, str2
int 21h
mov ah, 04ch
int 21h
end main
2) Without String Instruction:
.model small
.data
str1 db "0neWord$"
str2 db ?
.code
main:
mov ax, @data
mov ds, ax
mov si, 0
call copyStr
mov ah, 09h
lea dx, str2
int 21h
mov ah, 04ch
int 21h
copyStr proc
mov bx, 0
compute:
mov bl, str1 [si]
cmp bl, '0'
je alterChar
mov str2[si], bl
jmp continue
alterChar:
mov str2 [si], 'o'
continue:
inc si
cmp str1[si], '$'
je return
jmp compute
return:
mov str2[si], '$'
ret
copyStr endp
end main
LODSB Instruction you can learn more about string instructions from here
3) With lodsb / stosb and simplified / optimized:
.model small
.data
str1 db "0neWord$"
size equ $-str1
str2 db size dup ('')
.code
main:
mov ax, @data
mov ds, ax
mov es, ax ; stosb stores to [es:di]
mov si, OFFSET str1
mov di, OFFSET str2
cld ; make sure stosb/lodsb go forwards
; copy SI to DI, including the terminating '$'
copyStr: ; do {
lodsb ; str1 to al
cmp al, '0'
je alterChar
doneAlteration:
stosb ; al to str2
cmp al, '$'
jne copyStr ; } while(c != '$')
mov ah, 09h ; print implicit-length string
mov dx, OFFSET str2
int 21h
mov ah, 04ch ; exit
int 21h
alterChar:
mov al, 'o'
;jmp doneAlteration
stosb
jmp copyStr
end main
来源：https://stackoverflow.com/questions/40575898/how-to-use-strings-in-emu8086