Is there a way to get LaTeX to place figures in the same page as a reference to that figure?

问题

I am using LaTeX and the figure environment.

I am well familiar with the parameters to that environment: [htbp], and I am also generally familiar with the strategies that LaTeX takes, by default, to decide where to put each figure. For example, by placing figures at the top or bottom of the page.

What I am wondering is whether there is a package, macro, or some commands that I can give so that if I have a single-column document and I mostly have a single in-text reference to a figure, that the figure would be more likely to be placed in the same page of the reference?

For example, imagine that I have a long paragraph which in the middle has a \ref{FIG:X}. When rendered, some of the paragraph appears before the page break, and some appears after the page break. I can also place the figure command somewhere before and after the whole paragraph. Is there a way to get it to actually be placed in the same page as the actual reference?

回答1:

I don't want to sound too negative, but there are occasions when what you want is almost impossible without a lot of "artificial" tuning of page breaks.

If the callout falls naturally near the bottom of a page, and the figure falls on the following page, moving the figure back one page will probably displace the callout forward.

I would recommend (as far as possible, and depending on the exact size of the figures):

Place the figures with [t] (or [h] if you must)
Place the figures as near as possible to the "right" place (differs for [t] and [h])
Include the figures from separate files with \input, which will make them much easier to move around when you're doing the final tuning

In my experience, this is a big eater-up of non-available time (:-)

In reply to Jon's comment, I think this is an inherently difficult problem, because the LaTeX guys are no slouches. You may like to read Frank Mittelbach's paper.

回答2:

Yes, include float package into the top of your document and H (capital H) as a figure specifier:

\usepackage{float}

\begin{figure}[H]
.
.
.
\end{figure}

回答3:

You can always add the "!" into your float-options. This way, latex tries really hard to place the figure where you want it (I mostly use [h!tb]), stretching the normal rules of type-setting.

I have found another solution:
Use the float-package. This way you can place the figures where you want them to be.

回答4:

I solve this problem by always using the [h] option on floats (such as figures) so that they (mostly) go where I place them. Then when I look at the final draft, I adjust the location of the float by moving it in the LaTeX source. Usually that means moving it around the paragraph where it is referenced. Sometimes I need to add a page break at an appropriate spot.

I've found that the default placement of floats is reasonable in LaTeX, but manual adjustments are almost always needed to get things like this just right. (And sometimes it isn't possible for everything to be perfect when there are lots of floats and footnotes.)

The manual for the memoir class has some good information about how LaTeX places floats and some advice for manipulating the algorithm.

回答5:

Maybe this will help you?

\begin{center}
\includegraphics[scale=0.5]{picture_name}
\end{center}

I think is better to use the graphics command when your figures run away.

回答6:

I have some useful comments. Because I had similar problem with location of figures. I used package "wrapfig" that allows to make figures wrapped by text. Something like

...
\usepackage{wrapfig}
\usepackage{graphicx}
...
\begin{wrapfigure}{r}{53pt}
\includegraphics[width=53pt]{cone.pdf}
\end{wrapfigure}

In options {r} means to put figure from right side. {l} can be use for left side.

回答7:

\setcounter{topnumber}{2}
\setcounter{bottomnumber}{2}
\setcounter{totalnumber}{4}
\renewcommand{\topfraction}{0.85}
\renewcommand{\bottomfraction}{0.85}
\renewcommand{\textfraction}{0.15}
\renewcommand{\floatpagefraction}{0.7}

http://robjhyndman.com/researchtips/latex-floats/

回答8:

If you want force this behaviour on all of your figures try

...
\usepackage{float}
\floatplacement{figure}{H}
...

回答9:

One way I found that helps with this is to use \include{file_with_tex_figure_commands}

(not input)

来源：https://stackoverflow.com/questions/448768/is-there-a-way-to-get-latex-to-place-figures-in-the-same-page-as-a-reference-to

标签

latex

figures