Why does TCP connection keep closing while connecting to xively from Adruino GPRS with AT commands?

别等时光非礼了梦想. 提交于 2020-01-04 14:28:32

问题


I'm trying to send data from a cellular-connected arduino temperature sensor to xively.com using AT commands. I can open the TCP connection, but then it immediately closes. Why does the TCP connection keep closing?

setup: arduino uno mackbook seeedstudio gprs v2.0 att gophone sim card

Here is my Terminal readout:

Call Ready
AT

OK
AT+CPIN?

+CPIN: READY

OK
AT+CGATT?

+CGATT: 1

OK
AT+CIPSHUT

SHUT OK
AT+CIPSTATUS

OK

STATE: IP INITIAL
AT+CIPMUX=0

OK
AT+CSTT="wap.cingular"

OK
AT+CIICR

OK
AT+CIFSR

10.52.49.206
AT+CIPSTART="TCP","api.xively.com","80"

OK

STATE: TCP CLOSED

my setup: SEEEDStudio GPRS shield Arduino Uno macbook

To send AT commands to the sheild, I have set up a serial relay using the following code:

//Serial Relay - Arduino will patch a 
//serial link between the computer and the GPRS Shield
//at 19200 bps 8-N-1
//Computer is connected to Hardware UART
//GPRS Shield is connected to the Software UART 

#include <SoftwareSerial.h>

SoftwareSerial GPRS(7, 8);
unsigned char buffer[64]; // buffer array for data recieve over serial port
int count=0;     // counter for buffer array 
void setup()
{
  GPRS.begin(19200);               // the GPRS baud rate   
  Serial.begin(19200);             // the Serial port of Arduino baud rate.

}

void loop()
{
  if (GPRS.available())              // if date is comming from softwareserial port ==> data is comming from gprs shield
  {
    while(GPRS.available())          // reading data into char array 
    {
      buffer[count++]=GPRS.read();     // writing data into array
      if(count == 64)break;
  }
    Serial.write(buffer,count);            // if no data transmission ends, write buffer to hardware serial port
    clearBufferArray();              // call clearBufferArray function to clear the storaged data from the array
    count = 0;                       // set counter of while loop to zero


  }
  if (Serial.available())            // if data is available on hardwareserial port ==> data is comming from PC or notebook
    GPRS.write(Serial.read());       // write it to the GPRS shield
}
void clearBufferArray()              // function to clear buffer array
{
  for (int i=0; i<count;i++)
    { buffer[i]=NULL;}                  // clear all index of array with command NULL
}

I then enter the commands and monitor serial communication with CoolTerm.


回答1:


This works for me:

send AT+CGREG? until you get +CGREG: 0,1
send AT+CGATT? response +CGATT: 1
send AT+CSTT="internet","","" response OK
send AT+CIICR response OK
send AT+CIFSR response IP address
send AT+CIPSTART="TCP","api.xively.com","80" response CONNECT OK


来源:https://stackoverflow.com/questions/25634804/why-does-tcp-connection-keep-closing-while-connecting-to-xively-from-adruino-gpr

易学教程内所有资源均来自网络或用户发布的内容,如有违反法律规定的内容欢迎反馈
该文章没有解决你所遇到的问题?点击提问,说说你的问题,让更多的人一起探讨吧!