How to insert text at beginning of a multi-line selection in vi/Vim

问题

In Vim, how do I insert characters at the beginning of each line in a selection?

For instance, I want to comment out a block of code by prepending // at the beginning of each line assuming my language's comment system doesn't allow block commenting like /* */. How would I do this?

回答1:

Press Esc to enter 'command mode'
Use Ctrl+V to enter visual block mode
Move Up/Downto select the columns of text in the lines you want to comment.
Then hit Shift+i and type the text you want to insert.
Then hit Esc, wait 1 second and the inserted text will appear on every line.

For further information and reading, check out "Inserting text in multiple lines" in the Vim Tips Wiki.

回答2:

This replaces the beginning of each line with "//":

:%s!^!//!

This replaces the beginning of each selected line (use visual mode to select) with "//":

:'<,'>s!^!//!

Note that gv (in normal mode) restores the last visual selection, this comes in handy from time to time.

回答3:

The general pattern for search and replace is:

:s/search/replace/

Replaces the first occurrence of 'search' with 'replace' for current line

:s/search/replace/g

Replaces all occurrences of 'search' with 'replace' for current line, 'g' is short for 'global'

This command will replace each occurrence of 'search' with 'replace' for the current line only. The % is used to search over the whole file. To confirm each replacement interactively append a 'c' for confirm:

:%s/search/replace/c

Interactive confirm replacing 'search' with 'replace' for the entire file

Instead of the % character you can use a line number range (note that the '^' character is a special search character for the start of line):

:14,20s/^/#/

Inserts a '#' character at the start of lines 14-20

If you want to use another comment character (like //) then change your command delimiter:

:14,20s!^!//!

Inserts a '//' character sequence at the start of lines 14-20

Or you can always just escape the // characters like:

:14,20s/^/\/\//

Inserts a '//' character sequence at the start of lines 14-20

If you are not seeing line numbers in your editor, simply type the following

:set nu

回答4:

Another way that might be easier for newcomers:

 some█
 code
 here

Place the cursor on the first line, e.g. by

: 1 Enter

and type the following to get into insert mode and add your text:

I / / Space

 // █some
 code
 here

Press Esc to get back to command mode and use the digraph:

j . j .

 // some
 // code
 //█here

j is a motion command to go down one line and . repeats the last editing command you made.

回答5:

And yet another way:

Move to the beginning of a line
enter Visual Block mode (CTRL-v)
select the lines you want (moving up/down with j/k, or jumping to a line with [line]G)
press I (that's capital i)
type the comment character(s)
press ESC

回答6:

This adds # at the beginning of every line:

:%s/^/#/

And people will stop complaining about your lack of properly commenting scripts.

回答7:

If you want to get super fancy about it, put this in your .vimrc:

vmap \c :s!^!//!<CR>
vmap \u :s!^//!!<CR>

Then, whenever in visual mode, you can hit \c to comment the block and \u to uncomment it. Of course, you can change those shortcut keystrokes to whatever.

回答8:

Yet another way:

:'<,'>g/^/norm I//

/^/ is just a dummy pattern to match every line. norm lets you run the normal-mode commands that follow. I// says to enter insert-mode while jumping the cursor to the beginning of the line, then insert the following text (two slashes).

:g is often handy for doing something complex on multiple lines, where you may want to jump between multiple modes, delete or add lines, move the cursor around, run a bunch of macros, etc. And you can tell it to operate only on lines that match a pattern.

回答9:

For commenting blocks of code, I like the NERD Commenter plugin.

Select some text:

Shift-V
...select the lines of text you want to comment....

Comment:

,cc

Uncomment:

,cu

Or just toggle the comment state of a line or block:

,c<space>

回答10:

I can recommend the EnhCommentify plugin.

eg. put this to your vimrc:

let maplocalleader=','
vmap <silent> <LocalLeader>c <Plug>VisualTraditional
nmap <silent> <LocalLeader>c <Plug>Traditional
let g:EnhCommentifyBindInInsert = 'No'
let g:EnhCommentifyMultiPartBlocks = 'Yes'
let g:EnhCommentifyPretty = 'Yes'
let g:EnhCommentifyRespectIndent = 'Yes'
let g:EnhCommentifyUseBlockIndent = 'Yes'

you can then comment/uncomment the (selected) lines with ',c'

回答11:

In case someone's multi-line-selection is actually a paragraph, there is no need to manually select the lines. vim can do that for you:

vip: select and mark the whole paragraph
shift-i: insert text at line beginning
escape: leave insert mode/enter normal mode [line beginnings still selected]
escape: unselect line beginnings

回答12:

Mark the area to be comment as a visual block (<C-V)

and do c#<ESC>p

change it to "#"
put it back

If you do it often, define a short cut (example \q) in your .vimrc

:vmap \q c#<ESC>p

回答13:

To insert "ABC" at the begining of each line:

1) Go to command mode

2) :% norm I ABC

来源：https://stackoverflow.com/questions/253380/how-to-insert-text-at-beginning-of-a-multi-line-selection-in-vi-vim

标签

vim

editing

viemu