问题
So i recently successfully built a system which will record, plot, and playback an audio wav file entirely with python. Now, I'm trying to put some filtering and audio mixing in between the when i record and when i start plotting and outputting the file to the speakers. However, i have no idea where to start. Right now I'm to read in a the intial wav file, apply a low pass filter, and then re-pack the newly filtered data into a new wav file. Here is the code i used to plot the initial data once i recorded it.
import matplotlib.pyplot as plt
import numpy as np
import wave
import sys
spf = wave.open('wavfile.wav','r')
#Extract Raw Audio from Wav File
signal = spf.readframes(-1)
signal = np.fromstring(signal, 'Int16')
plt.figure(1)
plt.title('Signal Wave...')
plt.plot(signal)
And here is some code i used to generate a test audio file of a single tone:
import numpy as np
import wave
import struct
freq = 440.0
data_size = 40000
fname = "High_A.wav"
frate = 11025.0
amp = 64000.0
sine_list_x = []
for x in range(data_size):
sine_list_x.append(np.sin(2*np.pi*freq*(x/frate)))
wav_file = wave.open(fname, "w")
nchannels = 1
sampwidth = 2
framerate = int(frate)
nframes = data_size
comptype = "NONE"
compname = "not compressed"
wav_file.setparams((nchannels, sampwidth, framerate, nframes,
comptype, compname))
for s in sine_list_x:
wav_file.writeframes(struct.pack('h', int(s*amp/2)))
wav_file.close()
I'm not really sure how to apply said audio filter and repack it, though. Any help and/or advice you could offer would be greatly appreciated.
回答1:
First step : What kind of audio filter do you need ?
Choose the filtered band
- Low-pass Filter : remove highest frequency from your audio signal
- High-pass Filter : remove lowest frequencies from your audio signal
- Band-pass Filter : remove both highest and lowest frequencies from your audio signal
For the following steps, i assume you need a Low-pass Filter.
Choose your cutoff frequency
The Cutoff frequency is the frequency where your signal will be attenuated by -3dB.
Your example signal is 440Hz, so let's choose a Cutoff frequency of 400Hz. Then your 440Hz-signal is attenuated (more than -3dB), by the Low-pass 400Hz filter.
Choose your filter type
According to this other stackoverflow answer
Filter design is beyond the scope of Stack Overflow - that's a DSP problem, not a programming problem. Filter design is covered by any DSP textbook - go to your library. I like Proakis and Manolakis' Digital Signal Processing. (Ifeachor and Jervis' Digital Signal Processing isn't bad either.)
To go inside a simple example, I suggest to use a moving average filter (for a simple low-pass filter).
See Moving average
Mathematically, a moving average is a type of convolution and so it can be viewed as an example of a low-pass filter used in signal processing
This Moving average Low-pass Filter is a basic filter, and it is quite easy to use and to understand.
The parameter of the moving average is the window length.
The relationship between moving average window length and Cutoff frequency needs little bit mathematics and is explained here
The code will be
import math
sampleRate = 11025.0
cutOffFrequency = 400.0
freqRatio = (cutOffFrequency/sampleRate)
N = int(math.sqrt(0.196196 + freqRatio**2)/freqRatio)
So, in the example, the window length will be 11
Second step : coding the filter
Hand-made moving average
see specific discussion on how to create a moving average in python
Solution from Alleo is
def running_mean(x, windowSize):
cumsum = numpy.cumsum(numpy.insert(x, 0, 0))
return (cumsum[windowSize:] - cumsum[:-windowSize]) / windowSize
filtered = running_mean(signal, N)
Using lfilter
Alternatively, as suggested by dpwilson, we can also use lfilter
win = numpy.ones(N)
win *= 1.0/N
filtered = scipy.signal.lfilter(win, [1], signal).astype(channels.dtype)
Third step : Let's Put It All Together
import matplotlib.pyplot as plt
import numpy as np
import wave
import sys
import math
import contextlib
fname = 'test.wav'
outname = 'filtered.wav'
cutOffFrequency = 400.0
# from http://stackoverflow.com/questions/13728392/moving-average-or-running-mean
def running_mean(x, windowSize):
cumsum = np.cumsum(np.insert(x, 0, 0))
return (cumsum[windowSize:] - cumsum[:-windowSize]) / windowSize
# from http://stackoverflow.com/questions/2226853/interpreting-wav-data/2227174#2227174
def interpret_wav(raw_bytes, n_frames, n_channels, sample_width, interleaved = True):
if sample_width == 1:
dtype = np.uint8 # unsigned char
elif sample_width == 2:
dtype = np.int16 # signed 2-byte short
else:
raise ValueError("Only supports 8 and 16 bit audio formats.")
channels = np.fromstring(raw_bytes, dtype=dtype)
if interleaved:
# channels are interleaved, i.e. sample N of channel M follows sample N of channel M-1 in raw data
channels.shape = (n_frames, n_channels)
channels = channels.T
else:
# channels are not interleaved. All samples from channel M occur before all samples from channel M-1
channels.shape = (n_channels, n_frames)
return channels
with contextlib.closing(wave.open(fname,'rb')) as spf:
sampleRate = spf.getframerate()
ampWidth = spf.getsampwidth()
nChannels = spf.getnchannels()
nFrames = spf.getnframes()
# Extract Raw Audio from multi-channel Wav File
signal = spf.readframes(nFrames*nChannels)
spf.close()
channels = interpret_wav(signal, nFrames, nChannels, ampWidth, True)
# get window size
# from http://dsp.stackexchange.com/questions/9966/what-is-the-cut-off-frequency-of-a-moving-average-filter
freqRatio = (cutOffFrequency/sampleRate)
N = int(math.sqrt(0.196196 + freqRatio**2)/freqRatio)
# Use moviung average (only on first channel)
filtered = running_mean(channels[0], N).astype(channels.dtype)
wav_file = wave.open(outname, "w")
wav_file.setparams((1, ampWidth, sampleRate, nFrames, spf.getcomptype(), spf.getcompname()))
wav_file.writeframes(filtered.tobytes('C'))
wav_file.close()
回答2:
sox library can be used for static noise removal.
I found this gist which has some useful commands as examples
来源：https://stackoverflow.com/questions/24920346/filtering-a-wav-file-using-python