Exact dimensions of linetype spacing and size

问题

This is mostly a follow-up question on a previous one.

Given that in ggplot2 and grid there are different linetypes and spacings vary between line sizes, what is their relationship?

There are two things I do not quite understand.

How is the line size defined? If I were to draw a straight vertical line and substitute it by a rectangle, what should be the width of the rectangle to get the equivalent of the line's size? Especially, how does the lwd = 1 or lwd = 10 I pass to par()/gpar() relate to absolute dimensions (pixels, mm, inches, points)?

The gpar() documentation refers to the par() documentation which states the following:

The line width, a positive number, defaulting to 1. The interpretation is device-specific, and some devices do not implement line widths less than one.

Which is fair enough but I couldn't really find the necessary device specific documentation for common devices.

I think I might assume that the spacings of different linetypes are proportional to their size, but how exactly are the 'dotdash', 'dashed', 'dotted' etc. proportions of dash-length to spacing-length defined?

In the plot below, how can I predict or calculate the dash/spacing lengths in advance?

library(ggplot2)

df <- data.frame(
  x = rep(c(0, 1), 4),
  y = rep(1:4, each = 2),
  size = rep(c(2, 10), each = 4),
  linetype = rep(c(2,2,3,3), 2)
)

# The `I()` function automatically assigns identity scales
ggplot(df, aes(x, y, size = I(size), linetype = I(linetype))) +
  geom_line(aes(group = y))

I think this is mostly a documentation question, so I'd be happy if you could point me to the correct pages. Otherwise, an answer to my two questions above or a demonstration thereof would also be nice.

EDIT: ggplot has a variable called .pt which they use often to multiply a line size with. That probably means that in grid the linesize is something / .pt, but in what units?

回答1:

Another great question Teunbrand. I have a partial answer here which seems to give valid results but feels a bit imprecise.

The obvious way to get conversion between lwd and length units is to measure them programatically. For example, to check the lwd of the X11 device, you can do this:

library(grid)

x11()
grid.newpage()

# draw a thick black line that goes right across the page
grid.draw(linesGrob(x = unit(c(-0.1, 1.1), "npc"), 
                    y = unit(c(0.5, 0.5), "npc"),
                    gp = gpar(lwd = 10)))

# Capture as a bitmap
bmp_line    <- dev.capture()

# Work out the thickness of the line in pixels as proportion of page height
lwd_10_prop <- sum(bmp_line != "white")/length(bmp_line)

# Now draw a black rectGrob of known height with lwd of 0 and transparent for completeness
grid.newpage()
grid.draw(rectGrob(width  = unit(1.1, "npc"),
                   height = unit(10, "mm"),
                   gp     = gpar(lwd = 0, col = "#00000000", fill = "black")))

# Capture as a bitmap and measure the width as proportion of device pixels
bmp_rect    <- dev.capture()
mm_10_prop  <- sum(bmp_rect != "white")/length(bmp_rect)

# Get the ratio of lwd to mm
lwd_as_mm <- lwd_10_prop / mm_10_prop
dev.off()

lwd_as_mm
#> [1] 0.2702296

Which tells us that an lwd of 1 is 0.2702296 mm on this device

We can test this by plotting a red rectangle of our calculated width over a green line near the top of our page, then plotting the same green line over the same red rectangle near the bottom of the page. If and only if they are exactly the same width will we have a completely green line and a completely red line on our page:

grid.newpage()

grid.draw(linesGrob(x = unit(c(-0.1, 1.1), "npc"), 
                    y = unit(c(0.75, 0.75), "npc"),
                    gp = gpar(lwd = 5, col = "green")))

grid.draw(rectGrob(y = unit(0.75, "npc"),
                   width  = unit(1.1, "npc"),
                   height = unit(5 * lwd_as_mm, "mm"),
                   gp     = gpar(lwd = 0,  col = "#00000000", fill = "red")))

grid.draw(rectGrob(y = unit(0.25, "npc"),
                   width  = unit(1.1, "npc"),
                   height = unit(5 * lwd_as_mm, "mm"),
                   gp     = gpar(lwd = 0,  col = "#00000000", fill = "red")))

grid.draw(linesGrob(x = unit(c(-0.1, 1.1), "npc"), 
                    y = unit(c(0.25, 0.25), "npc"),
                    gp = gpar(lwd = 5, col = "green")))

Of course, we can improve precision by increasing the thickness of our lines when measuring how wide they are in pixels.

Although the result is supposed to be device-independent, it's worth noting that in the above example I took the results from the X11 device but plotted them in the rstudio device, so the equivalence seems to hold for both devices.

来源：https://stackoverflow.com/questions/63088587/exact-dimensions-of-linetype-spacing-and-size

标签

ggplot2

graphics

r-grid