问题
I cannot find whether named pipes are buffered, hence the question.
The manpage says https://linux.die.net/man/3/mkfifo:
A FIFO special file is similar to a pipe ... any process can open it for reading or writing, in the same way as an ordinary file.
Pipes are not buffered, no need to flush. But in a ordinary file, I would fflush (or fsync) the file descriptor.
How about named pipe?
回答1:
Pipes are not buffered, no need to flush.
I'd actually put that the other way around: for most intents and purposes, pipes are nothing but buffer. It is not meaningful to flush them because there is no underlying device to receive the data.
Moreover, although POSIX does not explicitly forbid additional buffering of pipe I/O, it does place sufficient behavioral requirements that I don't think there's any way to determine from observation whether such buffering occurs, except possibly by whether fsync() succeeds. In other words, even if there were extra buffering, it should not be necessary to fsync() a pipe end.
But in a ordinary file, I would fflush (or fsync) the file descriptor.
Well no, you would not fflush() a file descriptor. fflush() operates on streams, represented by FILE objects, not on file descriptors. This is a crucial distinction, because most streams are buffered at the C library level, independent of the nature of the file underneath. It is this library-level buffer that fflush() interacts with. You can control the library-level buffering mode of a stream via the setvbuf() function.
On those systems that provide it, fsync() operates at a different, lower level. It instructs the OS to ensure that all data previously written to the specified file descriptor has been delivered to the underlying storage device. In other words, it flushes OS-level buffers.
Note well that you can wrap a stream around a pipe-end file descriptor via the fdopen() function. That doesn't make the pipe require flushing any more than it did before, but the stream will be buffered by default, so flushing will be relevant to it.
Note, too, that some storage devices perform their own buffering, so that even after the data have been handed off to a storage device, it is not certain that they are immediately persistent.
How about named pipe?
The discussion above about stream I/O vs. POSIX descriptor-based I/O applies here, too. If you access a named pipe via a stream, then its interaction with fflush() will depend on the buffering of that stream.
But I suppose your question is more about os-level buffering and flushing. POSIX does not appear to say much concrete, but since you tag [linux] and refer to a Linux manual page in your question, I offer this in response:
The only difference between pipes and FIFOs is the manner in which they are created and opened. Once these tasks have been accomplished, I/O on pipes and FIFOs has exactly the same semantics.
(Linux pipe(7) manual page.)
回答2:
I don't understand quite well what you try to ask, but as you have been already told, pipes are not more than buffer.
Historically, fifos (or pipes) consumed the direct blocks of the inode used to maintain them, and they tied to a file (having it a name or not) in some filesystem.
Today, I don't know the exact implementation details for a fifo, but basically, the kernel buffers all data the writers have already written, but the readers haven't read yet. The fifo has an upper limit (system defined) for the amount of buffer they can support, but normally that fails around 10-20kb of data.
The kernel buffers, but there's no delay between writers and readers, because as soon a writer writes on a pipe, the kernel awakens all the readers waiting for it to have data. The reverse is also true, in the case the pipe gets full of data, as soon as a reader consumes it, all the writers are awaken to allow for filling it again.
Anyway, your question about flushing has nothing to do with pipes (well, not like, let me explain myself) but with <stdio.h> package. <stdio.h> does buffer, and it handles buffering on each FILE * individually, so you have calls for flushing buffers when you want them to be write(2)n to disk.
has a dynamic behaviour that allows to optimize buffering and not force programmers to have to flush at each time. That depends on the type of file descriptor associated with a FILE * pointer.
When the FILE * pointer is associated to a serial tty (it does check that calling to isatty(3) call, which internally makes an ioctl(2) call, that allow <stdio.h> to see if you are against a serial device, a char device. If this happens, then <stdio.h> does line buffering that means that always when a '\n' char is output to a device, the buffer is automatically buffered.
This supposes an optimization problem, because when, for example you are using cat(1) to copy a file, the largest the buffer normally supposes the most efficient approach. Well, <stdio.h> comes to solve the problem, because when output is not a tty device, it makes full buffering, and only flushes the internal buffers of the FILE * pointer when it is full of data.
So the question is: How does <stdio.h> behave with a fifo (or pipe) node? The answer is simple.... is is not a char device (or a tty) so <stdio.h> does full buffering on it. If you are communicating data between two processes and you want the reader to receive the data as soon as you have printf(3)ed it, then you have better to fflush(3), because if you don't, you can be waiting for a response that never comes, because what you have written, has not yet been written (not by the kernel, but by the <stdio.h> library)
As I said, I don't know if this is exactly the answer to your question, but for sure it can give you a hint on where the problem could be.
来源：https://stackoverflow.com/questions/50149805/do-i-need-to-flush-named-pipes