问题
My project has maybe 130 controls (total of all labels, textboxes, etc.) in an SSTab (4 tabs). The project loads fine, it runs fine, I don't see a single error or warning at any point, but when I save the form with the SStab on it, the SStab data isn't saved (it is completely gone). Normally the relevant portion of the .frm file looks like this:
Begin TabDlg.SSTab SSTab1
Height = 8895
[1550 more lines of code for all the controls]
Width = 540
End
Begin VB.Menu FileMenu
But lately it's getting cropped to:
Begin TabDlg.SSTab SSTab1 Begin VB.Menu FileMenu
This is very frustrating! In my VB IDE, the frame, sstab, and all the controls are there, editable, running/compiling fine, no error messages at any point, but when you save the file, 1550 lines of precious sstab data just disappears - again, with no warning or error messages. So if you exit and restart the IDE, you get a form load error because 60% of the code is now missing. The log file points to the first error it finds (in this case a Begin TabDlg with no End) - there's no other info in it. (The log file was generated after the code was deleted and saved, so it makes sense that it wouldn't be helpful.)
When I first posted this question, I thought it had to do with the number of controls, because it appeared after I added a control, and in my first few tests, seemed to disappear when that control (or other controls) was deleted. Now I can't seem to get that form to save under any circumstances, even when I delete many controls (bringing the number of controls far below where it was when it was last stable).
I also tried deleting the SStab and moving all the controls to 4 different frames. I successfully did that in the IDE, but when I saved, a huge chunk of the data (starting with a slider control) was missing. So I have no fraking idea what is going on.
The problem is reproducible on two different PCs, so it doesn't appear to be a hardware/corrupt software VB install issue.
Has anyone else run into something like this?
回答1:
Create a UserControl for each tab. That makes editing MUCH easier. It also allows you to nicely modularize the code, so each tab lives in its own file, and it'll allow you to reuse tabs elsewhere if you want.
回答2:
Sounds horrible, never heard of anything like that.
Presumably you aren't getting an error log file from VB6 when you load the form into the IDE before it gets corrupted? The log file has the same filename as the form file but with a .log filename extension. For example, if errors occurred when loading Myform.frm, Visual Basic would create a log file named Myform.log. The error messages you might see there are documented in the manual.
Have a look in the Windows Event Log, see whether it records any interesting problems against the VB6 IDE?
Are you using any weird controls? Maybe one of them is somehow corrupting the FRM or FRX. FRM files are just text as you obviously know & the format is documented in the VB6 manual. Can you see any corruption in the FRM in a text editor? If you remove any properties defined in the FRX, does it still fail.
I think I would try creating a new project and a new form, and then use the IDE to copy and paste all the control definitions into it - no code. Play with the new form, see whether it has the same problem. Maybe you can recreate the form this way without the problem. If the new form does have the problem, do the same thing but only take half the controls. Maybe you can find a problem control by "binary search".
回答3:
I get the same problem when attempting to save a form when the .FRM is writable but the .FRX is read-only
回答4:
Not sure if this is the issue, but on a VB6 form, there is a limit to 255 (or is it 256) named controls. Perhaps you are running into that?
One way around that limitation is to use control arrays. For example, if you had 10 labels, instead of label1, label2, label3, etc, you could do label(0) through label(9), and use up only one named control.
The other thing worth mentioning about the SSTAB is the way it shows/hides controls. While it may appear that the controls are on separate tabs, what is really happening is that the controls are getting moved waaaayyyyy to the left (and consequently out of view). Perhaps with so many components, the SSTAB is choking on this in the IDE as it tries to render the controls in design view?
Again, not sure if this is the issue, but I know these two tidbits are relatively unknown.
回答5:
So the SAVE function is not working.
I suspect one of the components you are placing on the tab strip is the culprit.
So ..
1) Take an inventory of each and every kind of component you are placing on the form
2) eliminate one (kind), SAVE
3) Did it SAVE?
-> Yes = that was the problematic control
-> No = return to step 2, but pick another kind
Of course, its important to remove all controls of a certain kind in step #2 (for example, ALL labels, or ALL textboxes, etc).
I have never heard of this happening however.
回答6:
You are not alone! I've seen this problem. . .in fact I'm dealing it right now, which is what brought me to this site.
I've been working with VB since '94 (VB3) and I first saw this problem about 5 or 6 years ago, while using VB6. My solution then, was not unlike some of the suggestions that you have recieved from the good folks who've responded above: throw out the existing file and rebuild the form in a new file. I did that back and the affected form has worked ever since.
My current problem is appearing in another, much newer form, and the replace/rebuild option (performed about a month ago) only worked for about three weeks. Now the problem is back and each new iteration of the file gets corrupted very quickly. Following the reply above regarding the total number of allowable controls, I'm looking into just how many controls I have. . .and, as it happens, I was in the process of consolidating the primary the buttons and menus into control arrays, simply because it was going to streamline their management.
I can also confirm your observations about moving the project to a second PC. . . I've done that too, and problem persists. Moreover, I can add that I have moved the project from one shared storage system to another to no avail. (The original storage location was on a drive mounted to a Win-tel system and the new location is on a UNIX-based NAS!)
Just rebuilt the file again and checked: Controls.Count = 62, so I am no where near the 255 control limit mentioned previously. This is indeed strange! (Not to mention furstrating!)
来源：https://stackoverflow.com/questions/712470/vb6-silently-deleting-huge-chunks-of-control-data-from-forms