Arm64 Linux Page Table Walk

问题

Currently I'm developing some research-related programs and I need to find the pte of some specific addresses. My development environment is Juno r1 board (CPUs are A53 and A57 ) and it's running arm64 Linux kernel.

I use some typical page table walk codes like this:

int find_physical_pte(void *addr)
{
    pgd_t *pgd;
    pud_t *pud;
    pmd_t *pmd;
    pte_t *ptep;
    unsigned long long address;

    address = (unsigned long long)addr;

    pgd = pgd_offset(current->mm, address);
    printk(KERN_INFO "\npgd is: %p\n", (void *)pgd);
    printk(KERN_INFO "pgd value: %llx\n", *pgd);
    if (pgd_none(*pgd) || pgd_bad(*pgd)) 
        return -1;

    pud = pud_offset(pgd, address);
    printk(KERN_INFO "\npud is: %p\n", (void *)pud);
    printk(KERN_INFO "pud value: %llx\n", (*pud).pgd);
    if (pud_none(*pud) || pud_bad(*pud))
        return -2;

    pmd = pmd_offset(pud, address);
    printk(KERN_INFO "\npmd is: %p\n", (void *)pmd);
    printk(KERN_INFO "pmd value: %llx\n",*pmd);
    if (pmd_none(*pmd) || pmd_bad(*pmd))
        return -3;

    ptep = pte_offset_kernel(pmd, address);
    printk(KERN_INFO "\npte is: %p\n", (void *)ptep);
    printk(KERN_INFO "pte value: %llx\n",*ptep);
    if (!ptep)
        return -4;

    return 1;
}

However, when the program checks the pte for the address(0xffffffc0008b2000), it always returns an empty pmd.

My guess is that I got the wrong pgd in the first step. I saw Tims Notes said that using current->mm only could get the pgd of TTBR0 (user space pgd) while the address I checked is a kernel space address so I should try to get the pgd of TTBR1.

So my question is: If I want to get the pte of a kernel space address, can I use current->mm to get the pgd?

If I can't, is there anything else I could try instead?

Any suggestion is welcome! Thank you.

Simon

回答1:

I think the problem you are having is that you are passing the struct mm_struct * pointer of the current process. But the address you are passing if from the kernel virtual address space. You need to pass the mm pointer to the init process (&init_mm):

pgd = pgd_offset(&init_mm, address);

I think the rest should be fine, but I haven't tested it. You can also look at how it is done in the kernel in the file arch/arm64/mm/dump.c

回答2:

I finally solved the problem.

Actually, my code is correct. The only part I missed is a page table entry check.

According to the page table design of ARMv8, ARM uses 4 levels page table for 4kb granule case. Each level (level 0-3 defined in the link) is implemented as pgd, pud, pmd, and ptep in Linux code.

In the ARM architecture, each level can be either block entry or the table entry (see the AArch64 Descriptor Format Section in the link).

If the memory address belongs to a 4kb table entry, then it needs to be traced down till level 3 entry (ptep). However, for the address belongs to a larger chunk, the corresponding table entry may save in the pgd, pud, or pmd level.

By checking the last 2 bits of the entry in each level, you know it's block entry or not and you only keep tracing down for the block entry.

Here is how to improve my code above:

Retrieving the descriptor based on the page table pointer desc = *pgd and then checking the last 2 bits of the descriptor.

If the descriptor is a block entry (0x01) then you need to extract the lower level entry as my code shows above. If you already get the table entry (0x11) at any level, then you can stop there and translate the VA to PA based on the descriptor desc you just get.

int find_physical_pte(void *addr)
{
    pgd_t *pgd;
    pud_t *pud;
    pmd_t *pmd;
    pte_t *ptep;
    unsigned long long address;

    address = (unsigned long long)addr;

    pgd = pgd_offset(current->mm, address);
    printk(KERN_INFO "\npgd is: %p\n", (void *)pgd);
    printk(KERN_INFO "pgd value: %llx\n", *pgd);
    if (pgd_none(*pgd) || pgd_bad(*pgd)) 
        return -1;
    //check if (*pgd) is a table entry. Exit here if you get the table entry.

    pud = pud_offset(pgd, address);
    printk(KERN_INFO "\npud is: %p\n", (void *)pud);
    printk(KERN_INFO "pud value: %llx\n", (*pud).pgd);
    if (pud_none(*pud) || pud_bad(*pud))
        return -2;
    //check if (*pud) is a table entry. Exit here if you get the table entry.   

    pmd = pmd_offset(pud, address);
    printk(KERN_INFO "\npmd is: %p\n", (void *)pmd);
    printk(KERN_INFO "pmd value: %llx\n",*pmd);
    if (pmd_none(*pmd) || pmd_bad(*pmd))
        return -3;
    //check if (*pmd) is a table entry. Exit here if you get the table entry.

    ptep = pte_offset_kernel(pmd, address);
    printk(KERN_INFO "\npte is: %p\n", (void *)ptep);
    printk(KERN_INFO "pte value: %llx\n",*ptep);
    if (!ptep)
        return -4;

    return 1;
}

来源：https://stackoverflow.com/questions/42963312/arm64-linux-page-table-walk