How to properly set up serial communication on Linux

问题

I'm attempting to read and write data from and to an FPGA board. The board itself came with a driver that create a terminal device called ttyUSB0 whenever the board is plugged in. On the FPGA, an asynchronous receiver and transmitter were implemented, and they seem to work.

However, there seems to be an issue on C side of things. I've been using some test vectors to test if the FPGA is outputting the proper information. I've noticed a few things things:

The device sometimes does not open correctly
The terminal attributes sometimes fail to be retrieved or set.
The read is sometimes non-blocking and doesn't retrieve the proper value.

Below is how I set up terminal and file descriptor options. Much of it was taken from here: http://slackware.osuosl.org/slackware-3.3/docs/mini/Serial-Port-Programming

Any advice or comments as to why the program may be failing would be greatly helpful.

#include <stdio.h>   // Standard input/output definitions
#include <string.h>  // String function definitions
#include <unistd.h>  // UNIX standard function definitions
#include <fcntl.h>   // File control definitions
#include <errno.h>   // Error number definitions
#include <termios.h> // POSIX terminal control definitions

int open_port(void){

    int fd;    // File descriptor for the port
    fd = open("/dev/ttyUSB0", O_RDWR | O_NOCTTY);

    if (fd == -1){
        fprintf(stderr, "open_port: Unable to open /dev/ttyUSB0 %s\n",strerror(errno));
        exit(EXIT_FAILURE);
    }

    return (fd);
}

int main(void){

    int fd = 0;              // File descriptor
    struct termios options;  // Terminal options

    fd = open_port();    // Open tty device for RD and WR

    fcntl(fd, F_SETFL);            // Configure port reading
    tcgetattr(fd, &options);       // Get the current options for the port
    cfsetispeed(&options, B230400);    // Set the baud rates to 230400
    cfsetospeed(&options, B230400);

    options.c_cflag |= (CLOCAL | CREAD);    // Enable the receiver and set local mode
    options.c_cflag &= ~PARENB;             // No parity bit
    options.c_cflag &= ~CSTOPB;             // 1 stop bit
    options.c_cflag &= ~CSIZE;              // Mask data size
    options.c_cflag |=  CS8;                // Select 8 data bits
    options.c_cflag &= ~CRTSCTS;            // Disable hardware flow control  

    // Enable data to be processed as raw input
    options.c_lflag &= ~(ICANON | ECHO | ISIG);

    // Set the new attributes
    tcsetattr(fd, TCSANOW, &options);

    ////////////////////////////////////
    // Simple read and write code here//
    ////////////////////////////////////

    // Close file descriptor & exit
    close(fd)
    return EXIT_SUCCESS
}

UPDATE I've modified my code based on the first answer. This is what I have now:

#include <errno.h>      // Error number definitions
#include <stdint.h>     // C99 fixed data types
#include <stdio.h>      // Standard input/output definitions
#include <stdlib.h>     // C standard library
#include <string.h>     // String function definitions
#include <unistd.h>     // UNIX standard function definitions
#include <fcntl.h>      // File control definitions
#include <termios.h>    // POSIX terminal control definitions

// Open usb-serial port for reading & writing
int open_port(void){

    int fd;    // File descriptor for the port
    fd = open("/dev/ttyUSB0", O_RDWR | O_NOCTTY);

    if (fd == -1){
        fprintf(stderr, "open_port: Unable to open /dev/ttyUSB0 %s\n",strerror(errno));
        exit(EXIT_FAILURE);
    }

    return fd;
}

int main(void){

    int              fd = 0;     // File descriptor
    struct termios   options;    // Terminal options
    int              rc;         // Return value

    fd = open_port();            // Open tty device for RD and WR

    // Get the current options for the port
    if((rc = tcgetattr(fd, &options)) < 0){
        fprintf(stderr, "failed to get attr: %d, %s\n", fd, strerror(errno));
        exit(EXIT_FAILURE);
    }

    // Set the baud rates to 230400
    cfsetispeed(&options, B230400);

    // Set the baud rates to 230400
    cfsetospeed(&options, B230400);

    cfmakeraw(&options);
    options.c_cflag |= (CLOCAL | CREAD);   // Enable the receiver and set local mode
    options.c_cflag &= ~CSTOPB;            // 1 stop bit
    options.c_cflag &= ~CRTSCTS;           // Disable hardware flow control
    options.c_cc[VMIN]  = 1;
    options.c_cc[VTIME] = 2;

    // Set the new attributes
    if((rc = tcsetattr(fd, TCSANOW, &options)) < 0){
        fprintf(stderr, "failed to set attr: %d, %s\n", fd, strerror(errno));
        exit(EXIT_FAILURE);
    }

    ////////////////////////////////
        // Simple Read/Write Code Here//
        ////////////////////////////////

    // Close file descriptor & exit
    close(fd);
    return EXIT_SUCCESS;
}

Just to clarify, the receiver and transmitter use 8 data bits, 1 stop bit, and no parity bit.

回答1:

I prefer Serial Programming Guide for POSIX Operating Systems.

You should delete the fcntl(mainfd, F_SETFL) statement, since it's not required and incorrectly implemented (F_GETFL not done prior and missing third argument).

Try using cfmakeraw to setup non-canonical mode, since your initialization code is incomplete:

options->c_iflag &= ~(IGNBRK | BRKINT | PARMRK | ISTRIP
        | INLCR | IGNCR | ICRNL | IXON);
options->c_oflag &= ~OPOST;

For non-canonical mode, you also need to define

options.c_cc[VMIN]  = 1;
options.c_cc[VTIME] = 2;

1 and 2 are just suggested values.

Add testing of return status after all system calls.

rc = tcgetattr(mainfd, &options);
if (rc < 0) {
    printf("failed to get attr: %d, %s\n", mainfd, strerror(errno));
    exit (-3);
}

Try testing with slower baudrates (e.g. 115200 or even 9600).

来源：https://stackoverflow.com/questions/15890903/how-to-properly-set-up-serial-communication-on-linux

标签

Linux

embedded

serial-port

termios