Optimization of count query for PostgreSQL

Question

I have a table in postgresql that contains an array which is updated constantly.

In my application i need to get the number of rows for which a specific parameter is

Answer 1

Is there an existing pattern I’m not aware of that applies to this situation? what would be the best approach for this?

Your best bet in this situation might be to normalize your schema. Split the array out into a table. Add a b-tree index on the table of properties, or order the primary key so it's efficiently searchable by property_id.

CREATE TABLE demo( id integer primary key );
INSERT INTO demo (id) SELECT id FROM arrtable;
CREATE TABLE properties (
  demo_id integer not null references demo(id),
  property integer not null,
  primary key (demo_id, property)
);
CREATE INDEX properties_property_idx ON properties(property);

You can then query the properties:

SELECT count(id) 
FROM demo 
WHERE NOT EXISTS (
  SELECT 1 FROM properties WHERE demo.id = properties.demo_id AND property = 1
)

I expected this to be a lot faster than the original query, but it's actually much the same with the same sample data; it runs in the same 2s to 3s range as your original query. It's the same issue where searching for what is not there is much slower than searching for what is there; if we're looking for rows containing a property we can avoid the seqscan of demo and just scan properties for matching IDs directly.

Again, a seq scan on the array-containing table does the job just as well.

Answer 2

PostgreSQL actually supports GIN indexes on array columns. Unfortunately, it doesn't seem to be usable for NOT ARRAY[...] <@ indexed_col, and GIN indexes are unsuitable for frequently-updated tables anyway.

Demo:

CREATE TABLE arrtable (id integer primary key, array_column integer[]);

INSERT INTO arrtable(1, ARRAY[1,2,3,4]);

CREATE INDEX arrtable_arraycolumn_gin_arr_idx
ON arrtable USING GIN(array_column);

-- Use the following *only* for testing whether Pg can use an index
-- Do not use it in production.
SET enable_seqscan = off;

explain (buffers, analyze) select count(id) 
from arrtable 
where not (ARRAY[1] <@ arrtable.array_column);

Unfortunately, this shows that as written we can't use the index. If you don't negate the condition it can be used, so you can search for and count rows that do contain the search element (by removing NOT).

You could use the index to count entries that do contain the target value, then subtract that result from a count of all entries. Since counting all rows in a table is quite slow in PostgreSQL (9.1 and older) and requires a sequential scan this will actually be slower than your current query. It's possible that on 9.2 an index-only scan can be used to count the rows if you have a b-tree index on id, in which case this might actually be OK:

SELECT (
  SELECT count(id) FROM arrtable
) - (
  SELECT count(id) FROM arrtable 
  WHERE (ARRAY[1] <@ arrtable.array_column)
);

It's guaranteed to perform worse than your original version for Pg 9.1 and below, because in addition to the seqscan your original requires it also needs an GIN index scan. I've now tested this on 9.2 and it does appear to use an index for the count, so it's worth exploring for 9.2. With some less trivial dummy data:

drop index arrtable_arraycolumn_gin_arr_idx ;
truncate table arrtable;
insert into arrtable (id, array_column)
select s, ARRAY[1,2,s,s*2,s*3,s/2,s/4] FROM generate_series(1,1000000) s;
CREATE INDEX arrtable_arraycolumn_gin_arr_idx
ON arrtable USING GIN(array_column);

Note that a GIN index like this will slow updates down a LOT, and is quite slow to create in the first place. It is not suitable for tables that get updated much at all - like your table.

Worse, the query using this index takes up to twice times as long as your original query and at best half as long on the same data set. It's worst for cases where the index is not very selective like ARRAY[1] - 4s vs 2s for the original query. Where the index is highly selective (ie: not many matches, like ARRAY[199]) it runs in about 1.2 seconds vs the original's 3s. This index simply isn't worth having for this query.

The lesson here? Sometimes, the right answer is just to do a sequential scan.

Since that won't do for your hit rates, either maintain a materialized view with a trigger as @debenhur suggests, or try to invert the array to be a list of parameters that the entry does not have so you can use a GiST index as @maniek suggests.

Answer 3

I think with Your current data model You are out of luck. Try to think of an algorithm that the database has to execute for Your query. There is no way it could work without sequential scanning of data.

Can You arrange the column so that it stores the inverse of data (so that the the query would be select count(id) from table where ARRAY[‘parameter value’] <@ table.array_column) ? This query would use a gin/gist index.