opengl - blending with previous contents of framebuffer

Question

I am rendering to a texture through a framebuffer object, and when I draw transparent primitives, the primitives are blended properly with other primitives drawn in that sin

Answer 1

I think there are two possible problems here.

Remember that all of the overlay lines are blended twice here. Once when they are blended into the FBO texture, and again when the FBO texture is blended over the scene.

So the first possibility is that you don't have blending enabled when drawing one line over another in the FBO overlay. When you draw into an RGBA surface with blending off, the current alpha is simply written directly into the FBO overlay's alpha channel. Then later when you blend the whole FBO texture over the scene, that alpha makes your lines translucent. So if you have blending against "the world" but not between overlay elements, it is possible that no blending is happening.

Another related problem: when you blend one line over another in "standard" blend mode (src alpha, 1 - src alpha) in the FBO, the alpha channel of the "blended" part is going to contain a blend of the alphas of the two overlay elements. This is probably not what you want.

For example, if you draw two 50% alpha lines over each other in the overlay, to get the equivalent effect when you blit the FBO, you need the FBO's alpha to be...75%. (That is, 1 - (1-.5) * (1-0.5), which is what would happen if you just drew two 50% alpha lines over your scene. But when you draw the two 50% lines, you'll get 50% alpha in the FBO (a blend of 50% with...50%.

This brings up the final issue: by pre-mixing the lines with each other before you blend them over the world, you are changing the draw order. Whereas you might have had:

blend(blend(blend(background color, model), first line), second line);

now you will have

blend(blend(first line, second line), blend(background color, model)).

In other words, pre-mixing the overlay lines into an FBO changes the order of blending and thus changes the final look in a way you may not want.

First, the simple way to get around this: don't use an FBO. I realize this is a "go redesign your app" kind of answer, but using an FBO is not the cheapest thing, and modern GL cards are very good at drawing lines. So one option would be: instead of blending lines into an FBO, write the line geometry into a vertex buffer object (VBO). Simply extend the VBO a little bit each time. If you are drawing less than, say, 40,000 lines at a time, this will almost certainly be as fast as what you were doing before.

(One tip if you go this route: use glBufferSubData to write the lines in, not glMapBuffer - mapping can be expensive and doesn't work on sub-ranges on many drivers...better to just let the driver copy the few new vertices.)

If that isn't an option (for example, if you draw a mix of shape types or use a mix of GL state, such that "remembering" what you did is a lot more complex than just accumulating vertices) then you may want to change how you draw into the VBO.

Basically what you'll need to do is enable separate blending; initialize the overlay to black + 0% alpha (0,0,0,0) and blend by "standard blending" the RGB but additive blending the alpha channels. This still isn't quite correct for the alpha channel but it's generally a lot closer - without this, over-drawn areas will be too transparent.

Then, when drawing the FBO, use "pre-multiplied" alpha, that is, (one, one-minus-src-alph).

Here's why that last step is needed: when you draw into the FBO, you have already multiplied every draw call by its alpha channel (if blending is on). Since you are drawing over black, a green (0,1,0,0.5) line is now dark green (0,0.5,0,0.5). If alpha is on and you blend normally again, the alpha is reapplied and you'l have 0,0.25,0,0.5.). By simply using the FBO color as is, you avoid the second alpha multiplication.

This is sometimes called "pre-multiplied" alpha because the alpha has already been multiplied into the RGB color. In this case you want it to get correct results, but in other cases, programmers use it for speed. (By pre-multiplying, it removes a mult per pixel when the blend op is performed.)

Hope that helps! Getting blending right when the layers are not mixed in order gets really tricky, and separate blend isn't available on old hardware, so simply drawing the lines every time may be the path of least misery.

Answer 2

As Ben Supnik said, the best way to do this is rendering the entire scene with separate blend functions for color and alpha. If you are using the classic non premultiplied blend function try glBlendFuncSeparateOES(GL_SRC_ALPHA, GL_ONE_MINUS_SRC_ALPHA, GL_ONE, GL_ONE) to render your scene to FBO. and glBlendFuncSeparateOES(GL_ONE, GL_ONE_MINUS_SRC_ALPHA) to render the FBO to screen.

It is not 100% accurate, but in most of the cases that will create no unexpected transparency.

Keep in mind that old Hardware and some mobile devices (mostly OpenGL ES 1.x devices, like the original iPhone and 3G) does not support separated blend functions. :(

Answer 3

Clear the FBO with transparent black (0, 0, 0, 0), draw into it back-to-front with

glBlendFuncSeparate(GL_SRC_ALPHA, GL_ONE_MINUS_SRC_ALPHA, GL_ONE, GL_ONE_MINUS_SRC_ALPHA);

and draw the FBO with

glBlendFunc(GL_ONE, GL_ONE_MINUS_SRC_ALPHA);

to get the exact result.

As Ben Supnik wrote, the FBO contains colour already multiplied with the alpha channel, so instead of doing that again with GL_SRC_ALPHA, it is drawn with GL_ONE. The destination colour is attenuated normally with GL_ONE_MINUS_SRC_ALPHA.

The reason for blending the alpha channel in the buffer this way is different:

The formula to combine transparency is

resultTr = sTr * dTr

(I use s and d because of the parallel to OpenGL's source and destination, but as you can see the order doesn't matter.)

Written with opacities (alpha values) this becomes

    1 - rA = (1 - sA) * (1 - dA)
<=> rA = 1 - (1 - sA) * (1 - dA)
       = 1 - 1 + sA + dA - sA * dA
       =         sA + (1 - sA) * dA

which is the same as the blend function (source and destination factors) (GL_ONE, GL_ONE_MINUS_SRC_ALPHA) with the default blend equation GL_FUNC_ADD.

---

As an aside:

The above answers the specific problem from the question, but if you can easily choose the draw order it may in theory be better to draw premultiplied colour into the buffer front-to-back with

    glBlendFunc(GL_ONE_MINUS_DST_ALPHA, GL_ONE);

and otherwise use the same method.

My reasoning behind this is that the graphics card may be able to skip shader execution for regions that are already solid. I haven't tested this though, so it may make no difference in practice.