Python, OpenCV: Increasing image brightness without overflowing UINT8 array

Question

I am trying to increase brightness of a grayscale image. cv2.imread() returns a numpy array. I am adding integer value to every element of the array. Theoretica

Answer 1

Briefly, you should add 50 to each value, find maxBrightness, then thisPixel = int(255 * thisPixel / maxBrightness)

You have to run a check for an overflow for each pixel. The method suggested by Divakar is straightforward and fast. You actually might want to increment (by 50 in your case) each value and then normalize it to 255. This would preserve details in bright areas of your image.

Answer 2

Here is another alternative:

# convert data type
gray = gray.astype('float32')

# shift pixel intensity by a constant
intensity_shift = 50
gray += intensity_shift

# another option is to use a factor value > 1:
# gray *= factor_intensity

# clip pixel intensity to be in range [0, 255]
gray = np.clip(gray, 0, 255)

# change type back to 'uint8'
gray = gray.astype('uint8)

Answer 3

An alternate approach that worked efficiently for me is to "blend in" a white image to the original image using the blend function in the PIL>Image library.

from PIL import Image
correctionVal = 0.05 # fraction of white to add to the main image
img_file = Image.open(location_filename)
img_file_white = Image.new("RGB", (width, height), "white")
img_blended = Image.blend(img_file, img_file_white, correctionVal)

img_blended = img_file * (1 - correctionVal) + img_file_white * correctionVal

Hence, if correctionVal = 0, we get the original image, and if correctionVal = 1, we get pure white.

This function self-corrects for RGB values exceeding 255.

Blending in black (RGB 0, 0, 0) reduces brightness.

Answer 4

I ran into a similar issue, but instead of addition, it was scaling image pixels in non-uniform manner.

The 1-D version of this:

a=np.array([100,200,250,252,255],dtype=np.uint8)
scaling=array([ 1.1,  1.2,  1.4,  1.2,  1.1])
result=np.uint8(a*scaling)

This gets you the overflow issue, of course; the result:

array([110, 240,  94,  46,  24], dtype=uint8)

The np.where works:

result_lim=np.where(a*scaling<=255,a*scaling,255)

yields result_lim as:

array([ 110.,  240.,  255.,  255.,  255.])

I was wondering about timing, I did this test on a 4000 x 6000 image (instead of 1D array), and found the np.where(), at least for my conditions, took about 2.5x times as long. Didn't know if there was a better/faster way of doing this. The option of converting to float, doing the operation, and then clipping as noted above was a bit slower than the np.where() method.

Don't know if there are better methods for this.

Answer 5

One idea would be to check before adding value whether the addition would result in an overflow by checking the difference between 255 and the current pixel value and checking if it's within value. If it does, we won't add value, we would directly set those at 255, otherwise we would do the addition. Now, this decision making could be eased up with a mask creation and would be -

mask = (255 - grey) < value

Then, feed this mask/boolean array to np.where to let it choose between 255 and grey+value based on the mask.

Thus, finally we would have the implementation as -

grey_new = np.where((255 - grey) < value,255,grey+value)

Sample run

Let's use a small representative example to demonstrate the steps.

In [340]: grey
Out[340]: 
array([[125, 212, 104, 180, 244],
       [105,  26, 132, 145, 157],
       [126, 230, 225, 204,  91],
       [226, 181,  43, 122, 125]], dtype=uint8)

In [341]: value = 100

In [342]: grey + 100 # Bad results (e.g. look at (0,1))
Out[342]: 
array([[225,  56, 204,  24,  88],
       [205, 126, 232, 245,   1],
       [226,  74,  69,  48, 191],
       [ 70,  25, 143, 222, 225]], dtype=uint8)

In [343]: np.where((255 - grey) < 100,255,grey+value) # Expected results
Out[343]: 
array([[225, 255, 204, 255, 255],
       [205, 126, 232, 245, 255],
       [226, 255, 255, 255, 191],
       [255, 255, 143, 222, 225]], dtype=uint8)

Testing on sample image

Using the sample image posted in the question to give us arr and using value as 50, we would have -